caricature

putty and caulking way

Preparation:
Putty will harden quickly, about 25 minutes after being mixed with the hardener.
Prepare fiber bodykit parts and fine sandpaper before using putty on it,
 make sure the surface clean of all dust and dirt, use a cleaning cloth.

Process practically putty in the final process of manufacture bodykit before getting into the paint. Caulking process is the hardest and dirtiest processes in all the processes that we have passed, but this process is the process of determining the end result of our work later. Finer detail and semaikin our work is guaranteed in the process of caulking the final outcome of the painting would be perfect

Mixing of putty to hardener:
Mixing putty and hardener are nearly the same as the dose of resin and catalyst mixing, for
more definitely try to read the instructions on the package using putty.
Once mixed, putty will change color, some yellow and green depending on the brand of putty.
Putty that has been blended for use for about 25 minutes, do not mix too much because the putty will get rid of useless.
Use a grading tool for mixing.
Once the mixture is ready, press the putty on the surface of the bodykit, the first thin writing and trying to close
The first uneven. In this section requires experience, try to continue to be. Drain about 1 hour.
A putty form:
Do not do this step before the putty dries, you will start from the beginning that make up the putty dry yet. How to check the putty is dry or not is by way of touching by hand, if it still feels wet and humid conditions means the putty is still not completely dry, dried again under the lights or the sun

Sanding:
Use sandpaper to rough metal surface to form a putty, sandpaper and sandpaper until smooth again, can go to other parts do not forget to use a cloth to clean the surface. If there is a small hole in the surface can be covered with putty on the next process.
Used sandpaper to smooth rough start, it will display fine lines on the surface, this is not a new problem because the first step of sanding. Fine sandpaper is used after the above process, sandpaper until smooth and slippery.
Caulking is actually a job that requires patience, technical caulking is a simple job and not too difficult
good luck

manner and process of making batik

                       sketches made ​​with pencil or pen sketches and then coated with wax using a canting

batik step 1

 dip into the first results of the first color and then repeat with the canting wax coating to dipped in the second

batik step 2

 repeat with the canting wax coating to dipped in the second color and so on

                                                      

                                                                      batik step 3



                                     as well as so on until all the desired color in the image sektsa

batik step 4

                               after all staining then dip in boiling water to remove all the wax layer

batik step 5

                                                                            this batik

                                       

airbrush paint magic

patchwork of damaged paint or paint magic, usually applied to repair collision-damaged paint or paint that is eroded due to friction or old paint.
damage to paint mainly due to the crunch or by accident, the damage is severe enough so that a surface is uneven and must be averaged to recover the form of a surface and then putty to smooth a surface.
if damaged due to minor collisions and only on clear coat. scratch-resistant coating and just need a little polish on the surface will eliminate scratch marks already, but if a collision will damage the color and should be color corrected and then coated with scratch-resistant coating.
is meant to restore the magic paint or re-color spray paint on the surface but no visible difference in the new paint to old paint, at this stage requires a mature technique, starting from mixing colors to color spray paint. , Each color each has its own technique for spliced ​​/ magic paint.
The first thing to note is the fineness of the surface to be painted the color and texture of surface, solid or metallic if metallic whether metallic patterned / rough textured or smooth textured and metallic colors only one color or more than one color, should then be seen under the sunlight or the light will seen clearly how the texture metallic color ..
car body in the present era is more likely to use a metallic color with a metallic texture more than one color
tried to mix the paint results in other media for comparison to the same color, if it is the same then spray on the desired surface does not have to cover the entire surface of the damaged portion only color only and do not forget to pay attention to the basic color of the color before the main color to be equated. because the base color greatly affects the outcome of the color display.
factor of the wind pressure on the compressor must be considered because it influences the results of the spray and spray distance should be considered let alone use a metallic color, do not let the metallic grains too much or too little.
spraying with adequate lighting, done under the sun or a lamp that can clearly see the metallic grains.
if finished then staying and finishing the finishing process of switching to thiner continued if the process of finishing / varnish covering the entire surface.
A good result finishing just need a little polish, polished to remove any dirt or residual dust / spray paint if the perceived bias sweep hand on the surface will feel rough, polished to produce a smooth surface and shiny paint.
good luck

techniques and process of making artificial marble

marble stone has several kinds of colors, most people were more familiar with the marble stone and beige hues tend to brown.
marble rock fans will certainly remove the contents of his pocket just to meet the delights of marble stone, what if you want extremely difficult to obtain, may be able to expencive or availability will be the desired marble stones are not available, for example wants pillars with a height of 40cm diameter 4m of 12 poles, is sufficient availability of marble stone for it. . .? and how long does it take? ,
therefore made ​​a replica or imitation of marble stone with paint.
The following are some steps to make artificial stone Mamer with paint:
- Concrete pillars that have been mashed with a layer of cement and then sprayed with a base color / epoxy in accordance with the color of the youngest of marble stone, Tear off the paper lengthwise with a width of between 2 to 6 cm is used as a mold line on the sternum cracks color marble stone color sprayed older of the basic colors, after spraying cracks and then use the line that has been folded gauze between 3 to 5 not to crease the folds tightly closed pores in gauze, use gauze fibers such as color printing, color spray-can be the same or older than color fracture line, repeat the spraying continues with a variety of fiber color brown to quite fill the empty space on the pillars, smooth spray color on the color that has not been evenly distributed in accordance with the flow. make a line of small cracks with black so as if it cracks in some parts of the pillar and then the last step to finish / clear / varnish to polish and add to the beauty of artificial stone Mamer. . . .
good luck.

techniques and process of making artificial stone granite

granite stone texture spots have a variety of color, there are white, bluish gray, toska, black with small spots and large all these irregular spots are formed.
imitation granite can be made on a media multiplex, wooden planks or concrete pillars, the media and multiplex wooden board recognized the existence of sanding and wood filer to close the pores on the surface of the multiplex and wooden planks. if it still looks porous then assisted with the putty until it is completely smooth a surface.
while the pillar must be sealed with cement concrete to be smooth. after a good smooth surface on the multiplex, wooden planks or concrete pillars and then given a primer / epoxy thick white base color, to form a grainy texture of the granite stones set the wind pressure on the tool pressurized spray gun to only 0.3 psi to 0.7 psi depending on the small spots desired texture. repeat spraying with a change of color to form a color pattern as in the texture of the granite stone.
after texture spots are sprayed granite stone texture has become like a granite stone there is the final step; ah finishing with clear / varnish, and must be repeated / multiple layers of texture to the surface of the spots that made ​​stone granite fully enclosed by a clear coating / varnish if it is dry touched hands will feel smooth without feeling rough spots.
congratulations and good luck . . . . .

airbrush techniques

In modern painting, air brush is known as one of painting that developed relatively recentlycompared with the conventional art, air brush can be said to be very different, especiallyon the tools in use. On the air brush equipment used in paint sprayer. Air brush artistsmore familiar with the term pen (pen brush). Today this technique is done by combining the work of three major equipment , compressor, air tank and a pen. Pump air produceaccommodated in the air tank. The air that collects in the tank the longer the higher the pressure is then released through the pen in the form of the wind. With the help of the windfrom the air tank, paint can out in the grains are very fine.
Air brush is an easy technique applied in the manufacture of paintings in particular, because it was using the power of the engine so it is very easy in the process of making good design could use techniques such as mold by making design and cut - cut to shapeits design. Air brusher  should be able to make design either manually or using acomputer with a variety of program design. Air brush can be applied in any media such asmedia fabric, wood, car license plate, motorcycle, fabrics, ceramics and so forth. The use ofcolors depending on the type of media that will be in the air brush. To be able to paint air brush with either the most basic need in the know are familiar with the characteristics ofthe air brush spray, the spraying needs to know the spraying air brush, air brush spraycharacteristics
will differ at a certain distance hasilnyapun will be different.


There are two techniques to draw air brush:
+ Print Technique, this technique using a mold that has been sketched drawings and inaccordance with the form image cuting.
+ Techniques Free Hand, air brush technique to draw directly without the help of molds orsketches.
In creating a painting / drawing both of these techniques complement each other. There are times when we need a firm line in a way that static free hand can not be obtained, as well asfree hand technique we can create a color gradation or memblur of thick ketipis of old coloror vice versa color kemuda young to the old color


The technique of painting / airbrush: - mold,-stripping, free-hand, etc.
Use brush effect with glitter / fosfor etc.
• penbrush application, spray gun and graphical techniques, with special additional toolssuch as brushes ,  markers, pen or pencil,  boxy. etc
• The element is the harmony of coloring which assessed the use of color, coloring,gradation and color combinations.
• Use brush effects, brushes and media innovation
-plastic mica / feathers  / gauze / cloth / yarn /cotton, etc. or other .
• The type of air brush is -realist - graphic - evolution - animation, ranging from design /motif, difficulty level, composition, narrative, detail, pattern, Grafity,, gradation, coloring,finishing, etc..